ahmed alobidani/Shutterstock
The idea of mesh networking has been around for several years. However, we didn’t start seeing the term pop up on wifi routers and devices until around the mid 2010s. That’s when companies like Eero, Google, and Netgear started rolling out “mesh networking kits,” which allowed you to blanket your home in a stronger wifi signal. Despite being around for several years now, the idea of mesh networking is still a bit foreign to many people. …..Continue reading…..
By: Joshua Hawkins
Source: Lifehacker
.
Critics:
A mesh network is a local area network topology in which the infrastructure nodes (i.e. bridges, switches, and other infrastructure devices) connect directly, dynamically and non-hierarchically to as many other nodes as possible and cooperate with one another to efficiently route data to and from clients. This lack of dependency on one node allows for every node to participate in the relay of information.
Mesh networks dynamically self-organize and self-configure, which can reduce installation overhead. The ability to self-configure enables dynamic distribution of workloads, particularly in the event a few nodes should fail. This in turn contributes to fault-tolerance and reduced maintenance costs.
Mesh topology may be contrasted with conventional star/tree local network topologies in which the bridges/switches are directly linked to only a small subset of other bridges/switches, and the links between these infrastructure neighbours are hierarchical. While star-and-tree topologies are very well established, highly standardized and vendor-neutral, vendors of mesh network devices have not yet all agreed on common standards, and interoperability between devices from different vendors is not yet assured.
Mesh networks can relay messages using either a flooding or a routing technique, which makes them different from non-mesh networks. A routed message is propagated along a path by hopping from node to node until it reaches its destination. To ensure that all its paths are available, the network must allow for continuous connections and must reconfigure itself around broken paths, using self-healing algorithms such as Shortest Path Bridging and TRILL (TRansparent Interconnection of Lots of Links).
Self-healing allows a routing-based network to operate when a node breaks down or when a connection becomes unreliable. The network is typically quite reliable, as there is often more than one path between a source and a destination in the network. Although mostly used in wireless situations, this concept can also apply to wired networks and to software interaction.
A mesh network whose nodes are all connected to each other is a fully connected network. Fully connected wired networks are more secure and reliable: problems in a cable affect only the two nodes attached to it. In such networks, however, the number of cables, and therefore the cost, goes up rapidly as the number of nodes increases.
Simple LANs in office or school buildings generally consist of cabling and one or more network switches; a switch is used to allow devices on a LAN to talk to one another via Ethernet. A switch can be connected to a router, cable modem, or ADSL modem for Internet access. LANs at residential homes usually tend to have a single router and often may include a wireless repeater. A LAN can include a wide variety of other network devices such as firewalls, load balancers, and network intrusion detection.
A wireless access point is required for connecting wireless devices to a network; when a router includes this device, it is referred to as a wireless router. Advanced LANs are characterized by their use of redundant links with switches using the spanning tree protocol to prevent loops, their ability to manage differing traffic types via quality of service (QoS), and their ability to segregate traffic with VLANs. A network bridge binds two different LANs or LAN segments to each other, often in order to grant a wired-only device access to a wireless network medium.
Network topology describes the layout of interconnections between devices and network segments. At the data link layer and physical layer, a wide variety of LAN topologies have been used, including ring, bus, mesh and star. The star topology is the most common in contemporary times. Wireless LAN (WLAN) also has its topologies: independent basic service set (IBSS, an ad-hoc network) where each node connects directly to each other (this is also standardized as Wi-Fi Direct), or basic service set (BSS, an infrastructure network that uses an wireless access point).
Local area networks may be connected to the Internet (a type of WAN) via fixed-line means (such as a DSL/ADSL modem) or alternatively using a cellular or satellite modem. These would additionally make use of telephone wires such as VDSL and VDSL2, coaxial cables, or fiber to the home for running fiber-optic cables directly into a house or office building, or alternatively a cellular modem or satellite dish in the latter non-fixed cases
With Internet access, the Internet service provider (ISP) would grant a single WAN-facing IP address to the network. A router is configured with the provider’s IP address on the WAN interface, which is shared among all devices in the LAN by network address translation. A gateway establishes physical and data link layer connectivity to a WAN over a service provider’s native telecommunications infrastructure.
Such devices typically contain a cable, DSL, or optical modem bound to a network interface controller for Ethernet. Home and small business class routers are often incorporated into these devices for additional convenience, and they often also have integrated wireless access point and 4-port Ethernet switch.
The ITU-T G.hn and IEEE Powerline standard, which provide high-speed (up to 1 Gbit/s) local area networking over existing home wiring, are examples of home networking technology designed specifically for IPTV delivery.
Leave a Reply